$15 Off On Order Over $100 Promo Code SAVE15
HOT SEARCH

Replacement Filter For:

Kenmore 10651182113

  • Filter Features
  • IAPMO Certified and meets NSF/ANSI standards 42

  • Remove chlorine, lead, mercury, cadmium, and thallium

  • Six months water filter service life

  • Easy and fast filter replacement

  • Largest Selection:
  • Enjoy better tasting drinking water with refrigerator water filter from Kenmore 10651182113. Clatterans carries wide range of refrigerator Kenmore filter replacements which is guaranteed by IAPMO and NSF/ANSI international water treatment standard 42 to fit your Unknown. The Unknown is working with activated carbon which will filter pesticides, industrial chemicals, chlorine taste and odor, other particulates efficiently. Filter your worries knowing your drinking water from Kenmore refrigerator with an ice and water dispenser  is safe and fresh to drink from Clatterans. 

Compatibility

Fits The Following Series

Kenmore Refrigerator Models

How to replace your filter

1. Locate the water filter in the top-right corner of the refrigerator compartment and open the cover door. The filter will be released and then be ejected as the door is opened.
 
2. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
 
3. Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
 
4. With the arrow pointing to the left (toward the filter cover door’s hinge), align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.
 
5. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.
 
6. Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hour
 
7. Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
 

Customer Review

RATING

4.8

OUT OF 5

TOTAL REVIEWS

551

SATISFACTION

96%

Top customer reviews

  • Great products for a great price!

    By Brandy on 2024-11-01 08:39:15

    Great price and great product! These are the only filters I buy. We only drink water from our refrigerator and this water tastes significantly better filtered from these filters. We’ve been using them for years and will continue.

  • Works great

    By Duane Cork on 2024-05-29 01:00:00

    Works great

  • Love it. Works perfect. Using this filter for years. Water tastes much better

    By Felice Sussman on 2024-05-28 09:21:21

    Love it. Work perfectly Have been ordering for years. Water tastes better. Easy to install. No mess.

  • It meet my expectations of clear water.

    By Mary Desel on 2024-05-25 01:00:00

    It meet my expectations of clear water.

  • Been using the filter for long while now. It work well just wish it would last a

    By YVONNE BAUMERT on 2024-05-21 01:00:00

    Been using the filter for long while now. It work well just wish it would last a bit longer than 6 months.

  • Good purchase will need every 6 months. So glad that I bought this.

    By Bob Batts on 2024-05-17 01:00:00

    Good purchase will need every 6 months. So glad that I bought this.

< >

    FAQ

    How often should you replace your water filter?
     
    - On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
     
    How do I turn off my filter light to reset?
     
    - If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
     
    Do the gaskets (o-rings) on the filters need to be lubricated?
     
    - Most water filters come with pre-lubricated O-rings
     
    - If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
     
    I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
     
    - You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
    Live Customer Support
    Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.

     

Find your refrigerator water filter in a few easy steps

What Brand Of Refrigerator Do You Have