$15 Off On Order Over $100 Promo Code SAVE15
HOT SEARCH

Replacement Filter For:

Whirlpool WRF989SDAW

  • Filter Features
  • NSF Certified 42 & 53

  • Filter Life: 6 Months

  • Filter Capacity: 200 Gallons

  • Largest Selection:
  • Clatterans Whirlpool refrigerator water filter comes up with a good solution for solving the headache water quality problems exist in your refrigerator wrf989sdaw. Whirlpool 46 9903,EDR2RXD1,EDR2RXD2 is IAPMO certified and meets NSF/ANSI standards 42, delivering preferable water for drinking or cooking. Designed to match various ordinary family needs, Whirlpool 46 9903,EDR2RXD1,EDR2RXD2 is provided in a reasonable price but not giving in its quality. Adopting a superb activated carbon, Whirlpool 46 9903,EDR2RXD1,EDR2RXD2 will pour out fast water and cool ice cubes from your Whirlpool refrigerator ice and water dispenser. Purchase a totally new filter from Clatterans to taste fresh water.    
     

Compatibility

How to replace your filter

1. Locate the accessory packet in the refrigerator and remove the water filter.
 
2. Take the water filter out of its packaging and remove the cover from the 0-rings. Be sure the 0-rings are still in place after the cover is removed.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
 
3. Align the arrow on the water filter label with the cutout notch in the filter housing and insert the filter into the housing.
 
4. Turn the filter clockwise until it locks into the housing.
NOTE: If the filter is not correctly locked into the housing, the water dispenser will not operate. Water will not flow from the dispenser.
 
5. While the compartment door is still open, lift the filter up into the compartment Then, close the filte compartment doo completely.
 
6. Run water from the dispenser for 5 minutes at .5 gp(about 2.5 gallons) to clear the system and preven sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hours.
 
7. Reset the "replace filter" light, if needed, by holding the reset button for three seconds.
 

Customer Review

RATING

4.9

OUT OF 5

TOTAL REVIEWS

447

SATISFACTION

98%

Top customer reviews

  • It was easy. To install and seems to work well

    By Donna Mayes on 2024-05-31 01:00:00

    It was easy. To install and seems to work well

  • Simple to install.just follow the arrows to insert.

    By Lataunya Wilmeth on 2024-05-27 01:00:00

    Simple to install.just follow the arrows to insert.

  • I have purchased this filter from you before. It’s easy to install and last ap

    By Randall Schuetz on 2024-05-20 01:00:00

    I have purchased this filter from you before. It’s easy to install and last approximately six months.

  • Amazing option This exactly what I was looking for Thanks

    By Katie Kiklis on 2024-05-18 01:00:00

    Amazing option This exactly what I was looking for Thanks

  • Filter was easy to install in the Refrigerator, it was a perfect fit.

    By SCARLETT RYAN on 2024-05-08 01:00:00

    Filter was easy to install in the Refrigerator, it was a perfect fit.

  • Perfect fit. Easy to install. Works properly.

    By Parker on 2024-05-04 01:00:00

    Perfect fit. Easy to install. Works properly.

< >

    FAQ

    Common Water Filter Questions
     
    How often should you replace your water filter?
     
    - On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
     
    How do I turn off my filter light to reset?
     
    - If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
     
    Do the gaskets (o-rings) on the filters need to be lubricated?
     
    - Most water filters come with pre-lubricated O-rings
     
    - If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
     
    I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
     
    - You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
     

Find your refrigerator water filter in a few easy steps

What Brand Of Refrigerator Do You Have