$15 Off On Order Over $100 Promo Code SAVE15
HOT SEARCH

Replacement Filter For:

Amana P4RFWB

  • Filter Features
  • IAPMO Certified and meets NSF/ANSI standards 42

  • Remove chlorine, lead, mercury, cadmium, and thallium

  • Six months water filter service life

  • Easy and fast filter replacement

  • Substitute your low efficient Amana refrigerator water filter and drink cleaner water with Clatterans Amana filter replacement which is IAPMO certified and meets NSF/ANSI standards 42, working perfectly with various refrigerator filter models like P4RFWB. The activated carbon P4RFWB using will expel the factors which will affect your health like dirt, rust, chlorine taste, odor, cyst, lead and other contaminants effectively. No tools needed to replace the filter inside your refrigerator, remember to change the P4RFWB at least six months or 300 gallons for the best filtration.

Compatibility

Fits The Following Series

GSC25C4 Series
GSF26C4 Series
GSS26C5 Series
WRF560 Series
WSF26C2 Series

Amana Refrigerator Models

How to replace your filter

1.Locate the water filter in the top-right corner of the refrigerator compartment and open the cover door. The filter will be released and then be ejected as the door is opened.

2.When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling may occur.Use a towel to wipe up any spills

3.Remove all packaging from the new filter. Remove all packaging covers from the O-rings. Make sure

4.With the filter’s arrow pointing to the left (towards the filter cover door’s hinge), align the new filter with the filter housing. Slide the new filter into place. The filter cover door will automatically begin to close as the new filter is inserted.

5.Close the filter cover door completely. This enables the new filter to nap fully into place. There is a Possibility that you may need to press hard when closing the filter door completely. This is normal

6.Run water from the dispenser for 5 minutes (approximately 3 gallons) to clear the system and prevent air from entering the system.
Note: The initial flow rate may be slower than expected. Full flow rate should be restored within 24-36 hours.

7.If needed, reset the Replace Filter light by holding the reset button for 3 seconds.

Customer Review

RATING

4.8

OUT OF 5

TOTAL REVIEWS

551

SATISFACTION

96%

Top customer reviews

  • I must say, this filter is outstanding.

    By Pat on 2024-01-09 00:00:00

    It arrived quickly and functions flawlessly. It's a fantastic product that I'm thoroughly satisfied with!

  • Highly recommended!

    By Bruce Deelaney on 2023-12-24 00:00:00

    This filter is truly exceptional, and the price is just right. I've had a great experience using it.

  • The filter meets all the factory requirements!

    By linwood Helbing on 2023-12-17 00:00:00

    It was the correct size for my fridge, and the installation process was a breeze.

  • I couldn't be happier!

    By Tamika` on 2023-12-10 00:00:00

    I'm delighted with the easy installation process and the fast shipping. The filter itself is excellent and comes at a reasonable price.

  • Just as expected

    By Michael Barilone on 2023-11-20 00:00:00

    The water tastes better than it has in a long time.

  • Great fit.

    By Kenneth Breau on 2023-11-07 00:00:00

    I'll always replace these filters whenever our refrigerator needs them. No complaints so far.

< >

    FAQ


    How often should you replace your water filter?

    - On average, most filters last 6 months or 300 gallons depending on your water quality and usage.

    How do I turn off my filter light to reset?

    - If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.

    Do the gaskets (o-rings) on the filters need to be lubricated?

    - Most water filters come with pre-lubricated O-rings

    - If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.

    I just installed my filter; do I need to run water through it before I drink the water? If so, how much?

    - You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!

Find your refrigerator water filter in a few easy steps

What Brand Of Refrigerator Do You Have