$15 Off On Order Over $100 Promo Code SAVE15
HOT SEARCH

Replacement Filter For:

Maytag MFD2562VEM10

  • Filter Features
  • Filter Life: 6-Months

  • Filter Capacity: 200 Gallon

  • Lead

  • Cysts

  • Asbestos

  • Largest Selection:
  • maytag refrigerator water filter at Clatterans will efficiently end up the life of chemicals which is bad for our human health plague in the water owing to its superlative activated carbon. The carbon will eliminate different kinds of heavy metals and contaminants which live safely in the water from the source or in pipes. Moreover, maytag 9006,4609030000,EDR4RXD1 mfd2562vem10 from Clatterans are all qualified by IAPMO and NSF/ ANSI drinking water treatment standards 42 to deliver premium and safe filtration outcomes. Find the right 9006,4609030000,EDR4RXD1 for your mfd2562vem10 to deliver clean, clear water that looks and tastes great.
     

Compatibility

Maytag Refrigerator Models

How to replace your filter

1. Locate the water filter in the top-right corner of the refrigerator compartment and open the cover door. The filter will be released and then be ejected as the door is opened.
 
2. When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling may occur. Use a towel to wipe up any spills.
 
3. Take the new filter out of its packaging and remove the covers from the O-rings. Be sure the O-rings are still in place after the covers are removed.
 
4. With the arrow pointing to the left (toward the filter cover door’s hinge), align the new filter with the filter housing and slide it into place. The filter cover door will automatically begin to close as the new filter is inserted.
 
5. Close the filter cover door completely in order to snap the filter into place. You may need to press hard.
 
6. Run water from the dispenser for 5 minutes at .5 gpm (about 2½ gallons) to clear the system and prevent sputtering.
NOTE: Initial rate may be slower than expected. Full rate should be restored within 24-36 hour
 
7. Reset the “replace filter” light, if needed, by holding the reset button for three seconds.
 

Customer Review

RATING

4.9

OUT OF 5

TOTAL REVIEWS

236

SATISFACTION

98%

Top customer reviews

  • arrived on time and was a great price

    By Lorayne McEwen on 2023-10-11 17:00:00

    Crystal clear water flows consistently; no more cloudy residue.

  • Easy to install & get working

    By Linda Stewart on 2023-09-27 17:00:00

    Effortless installation; replaced the filter in a minute.

  • Fits perfect

    By Debbi on 2023-08-22 17:00:00

    Noticeable taste improvement; water from my fridge now feels refreshing.

  • It is satisfactory.

    By Bonita on 2023-07-17 17:00:00

    It functions adequately, and it performs effectively.

  • It worked perfectly fine.

    By Karen Wright on 2023-06-20 17:00:00

    It is essential to flush the filter with at least 4 gallons of water before use. The water comes out clear and tastes fantastic.

  • Just what we needed

    By Gary Wilmouth on 2023-06-05 17:00:00

    I looked over a lot of the water filters that would go in my fridge and decided to stick with this one as it takes out so many more chemicals, minerals, etc. It is worth it good-tasting water!

< >

    FAQ

    How often should you replace your water filter?
     
    - On average, most filters last 6 months or 300 gallons depending on your water quality and usage.
     
    How do I turn off my filter light to reset?
     
    - If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.
     
    Do the gaskets (o-rings) on the filters need to be lubricated?
     
    - Most water filters come with pre-lubricated O-rings
     
    - If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.
     
    I just installed my filter; do I need to run water through it before I drink the water? If so, how much?
     
    - You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!
    Live Customer Support
    Our hours of operation are Monday thru Friday from 8:00am to 6:00pm Eastern Time and our after hours sales team is available 24 hours a day, 7 days a week. Whether it’s placing an order or answering questions that may help in your purchasing decisions, our specialists are ready to assist you. You can also contact us via email.
     

Find your refrigerator water filter in a few easy steps

What Brand Of Refrigerator Do You Have