$15 Off On Order Over $100 Promo Code SAVE15
HOT SEARCH

Replacement Filter For:

Whirlpool P4RFKB2

  • Filter Features
  • IAPMO Certified and meets NSF/ANSI standards 42

  • Remove chlorine, lead, mercury, cadmium, and thallium

  • Six months water filter service life

  • Easy and fast filter replacement

  • Substitute your low efficient Whirlpool refrigerator water filter and drink cleaner water with Clatterans Whirlpool filter replacement which is IAPMO certified and meets NSF/ANSI standards 42, working perfectly with various refrigerator filter models like P4RFKB2. The activated carbon P4RFKB2 using will expel the factors which will affect your health like dirt, rust, chlorine taste, odor, cyst, lead and other contaminants effectively. No tools needed to replace the filter inside your refrigerator, remember to change the P4RFKB2 at least six months or 300 gallons for the best filtration.

Compatibility

Fits The Following Series

GSC25C4 Series
GSF26C4 Series
GSS26C5 Series
WRF560 Series
WSF26C2 Series

Whirlpool Refrigerator Models

How to replace your filter

1.Locate the water filter in the top-right corner of the refrigerator compartment and open the cover door. The filter will be released and then be ejected as the door is opened.

2.When the door is completely open, pull the filter straight out.
NOTE: There may be some water in the filter. Some spilling may occur.Use a towel to wipe up any spills

3.Remove all packaging from the new filter. Remove all packaging covers from the O-rings. Make sure

4.With the filter’s arrow pointing to the left (towards the filter cover door’s hinge), align the new filter with the filter housing. Slide the new filter into place. The filter cover door will automatically begin to close as the new filter is inserted.

5.Close the filter cover door completely. This enables the new filter to nap fully into place. There is a Possibility that you may need to press hard when closing the filter door completely. This is normal

6.Run water from the dispenser for 5 minutes (approximately 3 gallons) to clear the system and prevent air from entering the system.
Note: The initial flow rate may be slower than expected. Full flow rate should be restored within 24-36 hours.

7.If needed, reset the Replace Filter light by holding the reset button for 3 seconds.

Customer Review

RATING

4.8

OUT OF 5

TOTAL REVIEWS

551

SATISFACTION

96%

Top customer reviews

  • Great products for a great price!

    By Brandy on 2024-11-01 08:39:15

    Great price and great product! These are the only filters I buy. We only drink water from our refrigerator and this water tastes significantly better filtered from these filters. We’ve been using them for years and will continue.

  • Works great

    By Duane Cork on 2024-05-29 01:00:00

    Works great

  • Love it. Works perfect. Using this filter for years. Water tastes much better

    By Felice Sussman on 2024-05-28 09:21:21

    Love it. Work perfectly Have been ordering for years. Water tastes better. Easy to install. No mess.

  • It meet my expectations of clear water.

    By Mary Desel on 2024-05-25 01:00:00

    It meet my expectations of clear water.

  • Been using the filter for long while now. It work well just wish it would last a

    By YVONNE BAUMERT on 2024-05-21 01:00:00

    Been using the filter for long while now. It work well just wish it would last a bit longer than 6 months.

  • Good purchase will need every 6 months. So glad that I bought this.

    By Bob Batts on 2024-05-17 01:00:00

    Good purchase will need every 6 months. So glad that I bought this.

    FAQ


    How often should you replace your water filter?

    - On average, most filters last 6 months or 300 gallons depending on your water quality and usage.

    How do I turn off my filter light to reset?

    - If the filter light will not reset after following specific instructions from your owner manual, contact your refrigerator manufacturer.

    Do the gaskets (o-rings) on the filters need to be lubricated?

    - Most water filters come with pre-lubricated O-rings

    - If you are having trouble installing the filter, we have found that a small amount of vegetable oil applied to the O-ring will ease installation and removal of the filter.

    I just installed my filter; do I need to run water through it before I drink the water? If so, how much?

    - You should run 3 gallons of water through your filter in order to flush it and make sure that it is thoroughly wet. Do not run the 3 gallons continuously, instead run the water for a few minutes and stop in between. Get a gallon water container, and pour and refill 3 times!